Saeed Hesaraki; Masoud Hafezi Ardakani; Kolsoum Rajabi Monavar; Hosein Mohammadi
Volume 7, Issue 3 , June 2013, , Pages 201-207
Abstract
In this research, effect of temperature and calcium to phosphorus (Ca/P) ratio of raw materials on the type and the amounts of formed phases were investigated by solid state method. Calcium carbonate and dicalcium phosphate were provided as raw materials and mixed with different percentages in a way ...
Read More
In this research, effect of temperature and calcium to phosphorus (Ca/P) ratio of raw materials on the type and the amounts of formed phases were investigated by solid state method. Calcium carbonate and dicalcium phosphate were provided as raw materials and mixed with different percentages in a way that final (Ca/P) ratio was between 1.50 to 1.67 in different batches. Then each of these mixtures was heated at temperatures of 800 to 1200 ° C for 3 hours. Phases were identified with XRD technique and quantitative assessment of phases was evaluated by RIR method and Chung relation. Results showed that in all relations and desired temperatures sintered below 1100 ° C beta tri-calcium phosphate is the dominant phase and hydroxyapatite present as second phase in the composition. In samples which sintered at 1200° C, beta TCP is transferred significantly to alpha TCP. In samples with Ca/p ratio: 1.62, 1.67, hydroxyapatite is dominant phase at 1200° C.
Rehabilitation Engineering
Mohammad Salehi Amini; Siavash Kazemirad; Saman Mohammadi; Roya Narimani; Farzam Farahmand
Volume 7, Issue 2 , June 2013, , Pages 121-132
Abstract
The purpose of this study was to design, analyze and evaluate an effective low-cost driving mechanism for gait trainer. The crank-rocker mechanism was favored for reproducing the path of foot during gait cycle, considering the type of motion and design parameters such as adjustability for different anthropometries, ...
Read More
The purpose of this study was to design, analyze and evaluate an effective low-cost driving mechanism for gait trainer. The crank-rocker mechanism was favored for reproducing the path of foot during gait cycle, considering the type of motion and design parameters such as adjustability for different anthropometries, providing sufficient space for interactions with physical therapist, and simplicity of execution. The dimensions of the mechanism were determined using optimization method while applying appropriate constraints so that the normal gait pattern, particularly of stance phase, was obtained. A 2-D model of the lower limb was developed to simulate the gait of a patient when using the mechanism. Results indicated that with appropriate positioning of the patient, the kinematic and kinetic patterns of the normal gait are reconstructed with no risk of injury. However, there is a high risk of injury of the knee articular surfaces and ligaments, if the patient is positioned only 3 cm higher than designed height.
Biomechanics of Bone / Bone Biomechanics
Hoda Salemi; Ali Asghar Behnamghader; Mohammad Reza Baghaban Eslaminejad; Mohammad Ataei
Volume 6, Issue 4 , June 2012, , Pages 249-255
Abstract
Collagen and Hydroxyapatite (HA) nanoparticles are significant constituent of the natural bone. In this study, the effect of collagen on the morphological and phase characteristics of calcium phosphate nanoparticles was investigated. The synthesis reaction was initiated by mixing H3PO4 as phosphorous ...
Read More
Collagen and Hydroxyapatite (HA) nanoparticles are significant constituent of the natural bone. In this study, the effect of collagen on the morphological and phase characteristics of calcium phosphate nanoparticles was investigated. The synthesis reaction was initiated by mixing H3PO4 as phosphorous source and CaCl2 as calcium source in presence of Collagen Type 1. Collagen concentration in suspension and Ca to P ratio was 1% and 1.67 respectively. The morphology and structure of samples (with collagen and without collagen), heat treated at 600 0C were characterized by X-Ray diffraction (XRD), Fourier transformation infrared (FTIR) and Scanning electron microscopy (SEM). More fine and flake-like shape particles were observed in the SEM images of sample synthesized in the presence of collagen compared to the control sample which was constituted of larger granular particles. The XRD results revealed the powders were composed of hydroxyapatite and octacalcium phosphate and the sample synthesized in the presence of collagen was less crystalline. The amide bands of collagen and P-O and OH characteristic peaks were identified in FT-IR spectra.
Vida Khalili; Jafar Khalil Allafi; Hosein Maleki Ghaleh
Volume 6, Issue 1 , June 2012, , Pages 9-15
Abstract
NiTi shape memory alloy cannot provide all the clinical requirements of an implant due to the high nickel content and bio-inert surface. Thus, its surface is coated by bio-ceramics such as hydroxyapatite (HA) in different methods in order to improve biocompatibility and bioactivity. In the present ...
Read More
NiTi shape memory alloy cannot provide all the clinical requirements of an implant due to the high nickel content and bio-inert surface. Thus, its surface is coated by bio-ceramics such as hydroxyapatite (HA) in different methods in order to improve biocompatibility and bioactivity. In the present study, a bio-active coating of HA using electrophoretic deposition technique was created on the surface of NiTi alloy to act as a barrier and prevent the diffusion of nickel ions in to the body fluid. A suspension was prepared by n-butanol as solvent and triethylenamine as dispersant. Coatings were deposited at different voltage of 40, 60 and 80 V for duration of 120s on the cathode. Then coated samples were sintered at 800 °C under argon atmosphere for 2 hrs. Evaluation of coatings was performed by X-ray diffraction techniques (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDX). Bioactivity and corrosion behavior of HA coatings was studied within simulated body fluid (SBF) environment. The results showed, the sample coated at 60 V is dense, uniform, owing proper corrosion resistant, and also the ability for nucleation and growth of apatite layer in SBF.
Vida Khalili; Jafar Khalil Allafi; Hosein Maleki Ghaleh
Volume 6, Issue 3 , June 2012, , Pages 231-238
Abstract
In this study, a hydroxyapatite/carbon nanotubes composite was coated at room temperature on NiTi shape memory alloy (SMA) through electrochemical deposition using stable suspension which was prepared by adding 4 g natural hydroxyapatite powder and 1 wt. % CNTs to 50 ml n-butanol. Suspension was stabilized ...
Read More
In this study, a hydroxyapatite/carbon nanotubes composite was coated at room temperature on NiTi shape memory alloy (SMA) through electrochemical deposition using stable suspension which was prepared by adding 4 g natural hydroxyapatite powder and 1 wt. % CNTs to 50 ml n-butanol. Suspension was stabilized using triethylenamine as dispersant. Surface characteristics, adhesion strength, stability and bioactivity of the composite coating were subsequently studied. EDX examination of the composite coating surface revealed homogeneous dispersion of carbon nanotubes all over coating. Also, the bonding strength of composite coating was found to be about 24 MPa. Compared to NiTi sample coated with hydroxyapatite and coated with hydroxyapatite/carbon nanotubes, the bode and nyquist plots of NiTi samples with hydroxyapatite/carbon nanotubes composite coating suggested that the composite coating was chemically more stable and provided corrosion resistance for NiTi SMA. In-vitro bioactivity test in SBF showed that the presence of CNTs in HA/CNTs composite coating does not have negative effect on ability of apatite formation.
Arghavan Farzadi; Mehran Solati Hashjin; Farhad Bakhshi; Alie Aminian
Volume 5, Issue 3 , June 2011, , Pages 206-213
Abstract
Using microwave irradiation in microwave-assisted synthesis method is a new approach employed to decrease synthesis time and to form more homogenous structures of biphasic calcium phosphate bioceramics. In this research, the microwave assisted synthesis and characterization of biphasic calcium phosphate ...
Read More
Using microwave irradiation in microwave-assisted synthesis method is a new approach employed to decrease synthesis time and to form more homogenous structures of biphasic calcium phosphate bioceramics. In this research, the microwave assisted synthesis and characterization of biphasic calcium phosphate nanopowders have been studied. The phase transformation, chemical components, morphology and particle size were characterized by X-Ray Diffraction (XRD) analysis, Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The results showed that the use of microwave led to improve crystallinity and the crystallite size increases from 16 nm to 27 nm. Also the amount of hydroxyapatite phase in biphasic calcium phosphate changed in the range of 5% to 17%. The prepared sample was put in Simulated Body Fluid (SBF).The pH of the solution was decreased in the present of beta-tricalcium phosphate showed its biodegradable behavior. Also the nucleation and growth of hydroxyapatite particles on TCP produced by microwave -assisted synthesis method changed to be rod like in SBF solution.
Nano-Biomaterials
Babak Farsadzadeh; Ali Asghar Behnamghader; Sedighe Joughedust
Volume 3, Issue 2 , June 2009, , Pages 151-160
Abstract
In this study hydroxyapatite (HA), flour-hydroxyapatite (FHA) and fluorapatite (FA) nanopowders synthesized by sol-gel route. Theses powders are used as biocompatible materials for bone replacement and teeth restoration. Ammonium fluoride (NH4F MERK), calcium nitrate [Ca(NO3)2,4H2O MERK] and triethyl ...
Read More
In this study hydroxyapatite (HA), flour-hydroxyapatite (FHA) and fluorapatite (FA) nanopowders synthesized by sol-gel route. Theses powders are used as biocompatible materials for bone replacement and teeth restoration. Ammonium fluoride (NH4F MERK), calcium nitrate [Ca(NO3)2,4H2O MERK] and triethyl phosphite [TEP, (C2H5O) 3P MERK)] were used as F, Ca and P precursors respectively. Triethyl phosphite was first hydrolyzed in ethanol with a small amount of distilled water. To prepare FHA and FA, an appropriate amount of the NH4F powder was added directly to TEP solution. The appropriate amounts of TEP solution was added dropwise to the calcium nitrate solution to yield a stoichiometric ratio of Ca/P=1.67. The resulted solution stirred for 1 h and aged at 25°C for 24 h and 40°C for 72h afterward. After oven drying at 80°C, the powder samples were heat-treated at 550°C for 1 h in air. Microstructural characteristics, powder morphology, chemical structure and phase analysis and in vitro study were performed by Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), X-Ray Diffraction (XRD), Fourier Transform Infra-Red (FTIR), Zetasizer instrument and cell culture method. Fluoride-substituted hydroxyapatite powders (FHA) and Fluor apatite (FA) were successfully fabricated via a sol–gel technique with the incorporation of different levels of fluoride ions. Nearly complete substitution of the OH¯ by F¯ occurred with heat treatment, which was confirmed by FTIR analysis. The particle size distribution of powders evaluated by a zeta-sizer instrument was 100-160nm. The XRD results showed that the crystal size of powders is 20-50nm. The phase stability and crystallinity were different depending on the level of fluoride substitution. Moreover, the crystallinity and crystallite size of the powders increased with fluoride substitution. These improvements in the crystallization and phase stability of the apatite structure, resulting from the fluoride substitution via the sol– gel process, suggest enhanced performance of the FHA powders. The cellular response to the HA, FHA and FA powder was assessed by an in vitro culture method using fibroblastic L929 cells. After culturing for 3 days, the results showed that the number of cells increased with increasing fluoride substitution.
Nader Nezafati; Fathollah Moztarzadeh; Saeed Hesaraki; Nasim Nosoudi
Volume 2, Issue 4 , June 2008, , Pages 277-283
Abstract
Calcium phosphate cements are among the formable calcium phosphate cements which are widely used for reconstruction of hard tissue injuries. Unfortunately, due to low mechanical strength, the application of such materials is only limited to non-load bearing like skull. We have investigated some mechanical ...
Read More
Calcium phosphate cements are among the formable calcium phosphate cements which are widely used for reconstruction of hard tissue injuries. Unfortunately, due to low mechanical strength, the application of such materials is only limited to non-load bearing like skull. We have investigated some mechanical and characteristics of a calcium phosphate cement which was reinforced with glass fiber. Compressed strength, setting time, phase composition and microstructure of the composite cement were among the cases which were investigated using appropriate techniques. The results indicated that adding only 15 weight percent of glass fiber (with about 100µm diameter) which was prepared using sol-gel method, does not show any meaningful change in the setting time of calcium phosphate cement This period of time was estimated about 20 minutes. Compressed strength of the cements without any fibers was 0.635MPa which was increased by adding fiber to 3.69MPa.The toughness of the cement was changed from 0.098KJ/m2 for cement without any fibers to 0.545KJ/m2 cement containing fibers. The XRD pattern of the composite samples which were maintained in the Ringer's solution showed that the reactant materials of the cement have almost thoroughly converted to hydroxyapatite which in this case does not show much difference with the non-fiber samples. As a whole, it seems that using glass fiber prepared by sol-gel method can considerably increase mechanical strength and toughness of calcium phosphate. This occurs without any effect on the quality of the cement.
Biomechanics of Bone / Bone Biomechanics
Seyed Mahmoud Rabiei; Fathollah Moztarzadeh; Mehran Solati Hashjin; Saeed Hesaraki
Volume 1, Issue 2 , June 2007, , Pages 105-110
Abstract
In this research, the influence of NaH2PO4.2H2O with different concentrations on setting time and compressive strength of bone cement based on hydroxyapatite was investigated. Hydroxyapatite cement is of calcium phosphate bone cements, which can be considered as the best substitute for hard tissues. ...
Read More
In this research, the influence of NaH2PO4.2H2O with different concentrations on setting time and compressive strength of bone cement based on hydroxyapatite was investigated. Hydroxyapatite cement is of calcium phosphate bone cements, which can be considered as the best substitute for hard tissues. The powder phase of the cement was prepared from various compositions of calcium phosphates such: tricalcium phosphate (TCP), calcium carbonate (CaCO3) and montite (CaHPO4) as constant and the liquid part using NaH2PO4.2H2O solution with different concentrations. The influences of liquid/powder ratio L/P (ml/g) was investigated on the initial and final setting times and compressive strengths of the cement. According to the obtained results, with optimum concentrations of the liquid phase, this cement seems suitable for clinical applications.
Nano-Biomaterials
Babak Mostaghasi; Mohammad Hossein Fathi; Mahmoud Sheikh Zeinaddin; Sabihe Soleimanianzad
Volume 1, Issue 2 , June 2007, , Pages 137-146
Abstract
Hydroxyapatite (HA) is a well known candidate for many applications in dentistry and medicine such as bone replacement and regeneration and coatings for medical implants. Nano-crystalline HA exhibits improved mechanical properties and biocompatibility. To optimize the benefits of nano-sized precursors, ...
Read More
Hydroxyapatite (HA) is a well known candidate for many applications in dentistry and medicine such as bone replacement and regeneration and coatings for medical implants. Nano-crystalline HA exhibits improved mechanical properties and biocompatibility. To optimize the benefits of nano-sized precursors, the particles must be of a uniform shape and size and have minimum degree of agglomeration. The aim of this study was to synthesize of nano-crystalline HA via the biomineralization route. For this purpose, an Iranian strain of Serratia (Serratia marcescens PTCC 1187) was utilized for the synthesis of nano-crystalline HA. The strain was cultivated. Then the pellet of S. marcescens PTCC 1187 was separated and exposed to Glycerol 2-phosphate and Calcium chloride. After 14 days of incubation at 37oC, the white precipitated material was separated. After drying and calcination at 600oC the powder was characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and fourier transform infrared spectroscopy (FTIR) techniques. The results showed that nano-structured HA powder was synthesized and the crystallinity of the powder was relatively high according to the standard. The particles of the powder were single crystal with the size of 25-30 nm. Moreover, the shape and size of the particles were relatively uniform and the agglomeration was lower comparing to the conventional methods. This powder could be used in the regeneration of bone defects, fabrication of medical, dental implants and also as a vector for pharmaceuticals and biological materials such as the genes.
Biomechanics of Bone / Bone Biomechanics
Khalil Farhangdoust; Ali Banihashem; Ali Ghaneei
Volume -2, Issue 1 , July 2005, , Pages 1-8
Abstract
Using ceramic coatings has increased in popularity due to their compatibility with bone, absence of the fibrous layer at the coating-implant interface, and the stronger coating-bone bonding. Among these coatings, hydroxyapatite (HA) and fluoroapatite (FA) are more popular. For the first time in this ...
Read More
Using ceramic coatings has increased in popularity due to their compatibility with bone, absence of the fibrous layer at the coating-implant interface, and the stronger coating-bone bonding. Among these coatings, hydroxyapatite (HA) and fluoroapatite (FA) are more popular. For the first time in this paper, modeling and stress analysis have been carried out for 24 implants in an axisymetric form using the finite element technique. Twelve of these samples belong to IMZ and the rest are from Dyna system. All implants had HA and FA coatings with thicknesses between 10 to 100 microns. The stress analysis results show that the stress concentration at the implant-coating and bone-coating bonding surfaces decreases with the increase of coating thickness. In addition, stress concentrations for implants with FA coatings are always more than those with HA coatings. In all implants, stress concentration has been observed around the bone crest.
Tissue Engineering
Karim Asgarzadeh Tabrizi; Fariba Ourang
Volume -1, Issue 1 , June 2004, , Pages 57-64
Abstract
Gelatin is a protein which is derived from the organic constituent of bone (collagen). Combination of this protein with the inorganic constituent of bone (hydroxyapatite) may provide closer properties to the natural bone. In this study, a biodegradable composite scaffold based on gelatin and hydroxyapatite ...
Read More
Gelatin is a protein which is derived from the organic constituent of bone (collagen). Combination of this protein with the inorganic constituent of bone (hydroxyapatite) may provide closer properties to the natural bone. In this study, a biodegradable composite scaffold based on gelatin and hydroxyapatite was prepared as a substitute for bone tissue. To increase the biocompatibility of this, composite, its fabrication was carried out without using any organic solvent. Porosities obtained were spontaneously achieved without any porogen. The pore morphology indicated a high interconnectivity with diameters ranging from 50 to 200 micrometers, which seems appropriate for bone tissue engineering applications. In order to study the biocompatibility of the scaffolds, mouse fibroblastic cells were used. After 24-hour cell culture period in vitro, suitable cell attachment was observed showing high biocompatibility for all the samples. Further examinations demonstrated that the best biocompatibility is obtained for the composite of 50 wt% hydroxyapatite and 50 wt% gelatin.
