Biomechanics / Biomechanical Engineering
Aminreza Noghrehabadi; Mohammad Hosein Heidarshenas; Reza Bahoosh
Volume 10, Issue 2 , August 2016, , Pages 123-136
Abstract
A two-dimensional-in-space mathematical model of amperometric micro biosensors with selective and perforated membranes has been proposed and analyzed. The model involves the geometry of micro or nano meter holes partially or fully filled with an enzyme. The model is based on a system of the reaction-diffusion ...
Read More
A two-dimensional-in-space mathematical model of amperometric micro biosensors with selective and perforated membranes has been proposed and analyzed. The model involves the geometry of micro or nano meter holes partially or fully filled with an enzyme. The model is based on a system of the reaction-diffusion equations containing a nonlinear term related to the Michaelis-Menten enzymatic reaction. In this study, in order to generate general equation, first, dimensionless parameters are introduced and then by replacing them into governing equation are converted to dimensionless equations.The general equations have been solved numerically in 2D space.. Using numerical simulation of the biosensor action, the influence of the geometry of the holes as well as of the filling level of the enzyme in the holes on the biosensor response was investigated. For this purpose three different geometries including cylindrical, upright circular and downright circular cone for cavities are considered and the impact of these geometries on the response of the biosensor in different levels of enzyme are obtained. Biosensor's respond based on rate of enzyme level variations to slope of the cone variations are determined. In the biosensor, as the level of enzyme rises in all three geometries, the biosensor output current increases. Under the same conditions, the sensitivity of biosensor in upright circular cone is more than the other two geometries and increases with a decrease in conical gradient. As long as the enzymatic properties are the same, the more biosensor's number, the more sensitivity.Moreover, a concept known as reduced dimensionless current is introduced by providing and calculating dimensionless current in the biosensor.
Seyed Hojat Sabzpoushan; Azadeh Ghajarjazy
Volume 9, Issue 3 , December 2015, , Pages 267-282
Abstract
Time constant is a physical concept that one may deduce the speed of response and reaction of a system from it. Experimental findings confirm the dependency of the speed of opening-closing of ionic channels to the membrane voltage. In this paper a model for time constant of membrane voltage in neurons ...
Read More
Time constant is a physical concept that one may deduce the speed of response and reaction of a system from it. Experimental findings confirm the dependency of the speed of opening-closing of ionic channels to the membrane voltage. In this paper a model for time constant of membrane voltage in neurons has been presented. At first, the presented model has been established as a theorem and then the theorem has been proved. According to the presented theorem, one can simulate different morphology and time course of action potential (AP) in neurons by adjusting the model parameters. The validation of the presented theorem (model) has been shown by simulation examples of some kinds of neurons and cells APs. Regarding the generality of the presented theorem, our model not only can be applied in biomedical systems but also it may be used in any physical systems.
Neuro-Muscular Engineering
Ali Esteki
Volume -1, Issue 1 , June 2004, , Pages 15-23
Abstract
Computer simulation of a three dimensional model of the thumb and index finger was used to perform a sensitivity analysis of each joint position to individual muscle activation level. The results were used to study the effect of each muscle on hand posture and select specific muscles to get a desired ...
Read More
Computer simulation of a three dimensional model of the thumb and index finger was used to perform a sensitivity analysis of each joint position to individual muscle activation level. The results were used to study the effect of each muscle on hand posture and select specific muscles to get a desired posture of the hand to assist the implementation of FNS systems. The hand was treated as a multi-body system including rigid segments connected by joints. Each joint was subjected to a total moment including muscle active and joint passive components. The forward approach, in which the equilibrium equations are solved for joint positions as a function of muscle moments, was used. The results showed that at the base joint of the index finger, flexion effect of the extrinsic flexor muscles was about two times of that of the intrinsic muscles. It was also shown that each muscle of the extensor system is individually more effective than the extrinsic flexor muscles. At the more distal joints, intrinsic muscles acted as feeble extensors. At the base joint of the thumb, extensor muscles were much more powerful than the flexor and flexor effect of adductor muscles. Also, abductor muscles were much more effective than the adductors. It was revealed that flexor muscles of the more distal joints are as strong as the extensor muscles. The conclusions are that: the minimum required muscles for appropriate positioning of the hand and for grasp and applying force to objects are limited.
